701Software, Enterprise Series (E Series) Controller and Home (H Series) Series Controller Full Command Table

2022-08-19

No. I005027-EN

Serial NO : I005027-EN

Date of Editing : 2022-08-19

Answer：

Note 1: ※ : Function noted with※ means that it is new updated. For Enterprise E series controller, the firmware version that support above functions should be released after 2022 April 19th; For Home H series controller, the firmware version should be released after 2022.

Note 2 : 20*/24*/28*/34* are multiple commands, please refer to "Function Default Value" Chapter to ensure the command.

1. Code/PWD Setting

Controller / Functions	Software	E Series Controller with LCD Screen	E Series Controller with Keypad	H Series Controller
Enter the Program Mode	❌	*PPPPPP# PPPPPP:Master Code，Default Value：123456	*PPPPPP# PPPPPP:Master Code，Default Value：123456	*PPPPPP# PPPPPP:Master Code，Default Value：123456
Master Code Modification			*09PPPPPPRRRRRR#** PPPPPP＝New master code RRRRRR＝Repeat the new master code	*09PPPPPPRRRRRR#** PPPPPP＝New master code RRRRRR＝Repeat the new master code
Setting Duress PWD			*15PPPP#** PPPP＝4-digit Code (0001-9999，default value：0000)	*(M4/M8)15PPPP#** PPPP＝4-digit Code (0001-9999，default value：4321)
Setting Arming PWD			*17PPPP#** PPPP＝4-digit Code (0001-9999，default value：1234)	*(M4/M8)17PPPP#** PPPP＝4-digit Code (0001-9999，default value：1234)
Setting Controller Language			❌	❌
※PIN / UID Length Range Setting	❌		*42mn#* m＝ PIN Length Range 4~8 n＝ UID Length Range 2~8	❌

2. Card Setting Commands

Controller / Functions	Software	E Series Controller with LCD Screen	E Series Controller with Keypad	H Series Controller
Suspend tag		Method 1: ------------------------------------------------------------------- Method 2:	*Suspend Invalid：10SSSSSEEEEE#* SSSSS＝Starting card number EEEEE＝Ending card number	*Suspend Invalid：10SSSSSEEEEE#* SSSSS＝Starting card number EEEEE＝Ending card number
Delete tag		Method 1: ------------------------------------------------------------------- Method 2:	*Remove： 10SSSSS9EEEEE#** SSSSS＝starting card number EEEEE＝ending card number	*Remove： 10SSSSS9EEEEE#** SSSSS＝starting card number EEEEE＝ending card number
Recover the suspended cards	Client->8.User Card Edit->Select user access mode		*11SSSSSEEEEE#* SSSSS＝starting card number EEEEE＝ending card number	*11SSSSSEEEEE#* SSSSS＝starting card number EEEEE＝ending card number
Card or PIN (M4/M8) Modify the PIN with user address, change the pass mode into Card or PIN			*12UUUUUPPPP~PPPPPPPP#* UUUUU＝User Address PPPP~PPPPPPPP＝4-digit(default)~8-digit code (Access by Card or PIN)	❌
Card and PIN (M4/M8) Modify the PIN with user address, change the pass mode into Card and PIN			*13UUUUUPPPP~PPPPPPPP#* UUUUU＝User Address PPPP~PPPPPPPP＝User Address; PPPP=4-digit PIN (0000~9999)	❌
Card number modification	Client->8.User Card Edit->User Card Edit -> Card ID		*16UUUUUSSSSSCCCCC#* UUUUU＝user address SSSSS＝5 digit site code CCCCC＝5 digit card code	*16UUUUUSSSSSCCCCC#* UUUUU＝user address SSSSS＝5 digit site code CCCCC＝5 digit card code
Add card by presenting	❌		*19UUUUUQQQQQ#* UUUUU＝user address QQQQQ＝Card quantity(00001=Continuously inducting)	(M4/M8 Mode) *19UUUUUQQQQQ#* UUUUU=user address QQQQQ=Card quantity (00001: for adding a single card or a batch of random numbering cards) (M6 Mode) - *22N#** N=0(Delete tag)/N=1(Add tag)
Master Card Setting (flashing card and pressing # to enter program mode, leaving program mode by flashing card again.)			*07SSSSSEEEEE#* SSSSS-EEEEE＝00000~15999 SSSSS＝starting user address EEEEE＝ending user address	(M4/M8 Mode) *07SSSSSEEEEE#* SSSSS-EEEEE(starting user address-ending user address)=00000-00255
Delete all tag			*2929#*	*2929#*
※Invalid Access Trigger Alarm (ex: swipe invalid card / PIN Code error / Time Zone error / Door Group error/ Anti-passback error)	❌	Auto enable after firmware upgrade	Enable 34002# Disable 34000#** (default value)	Enable 34002# Disable 34000#** (default value)
Enable/Disable Pass Any Cards			*36MW#** M=AR-725-E; W=WG Reader (0=disable; 1=enable)	Enter program mode->press 0# at the same time *24032#**
※Modify User Capacity / Floor / Alias	❌		User Capacity / Floor / Alias *430# : 16384 / 64 / 16 (default value) 431#* : 32768 / 32 / 16 *432#**: X/X/X	Home Series support different user capacity, 721H/757H support 1024 and 321H/331H/725H support 3000 users
※Enable / Disable 13.56MHz	❌		Enable: *34000#(default value) Disable: 34008#*	unique firmware
※Enable / Disable 125kHz	❌		Enable: *34000#(default value) Disable: 34016#*	unique firmware

3. Add / Delete Tags

Controller / Functions	Software	E Series Controller with LCD Screen	E Series Controller with Keypad	H Series Controller
Add Single Tag or Random Tags		-------------------------------------------------------------------	Enter program mode → *19UUUUU00001#* → Presenting Cards on Controller (00001: for adding a single card or a batch of random numbering cards)	Enter program mode → *19UUUUU00001#* → Presenting Cards on Controller (00001: for adding a single card or a batch of random numbering cards)
Add the Sequential Tags	❌		Enter Program Mode → *19UUUUUQQQQQ#* → Presenting First Card to Controller	Enter Program Mode → *19UUUUUQQQQQ#* → Presenting First Card to Controller
Delete Single Tag		-------------------------------------------------------------------	Enter Program Mode → *10SSSSSEEEEE#* SSSSS= starting user address / EEEEE= ending user address	Enter Program Mode → *10SSSSSEEEEE#* SSSSS= starting user address / EEEEE= ending user address
Delete Sequential Tags (sequential user address)			Enter Program Mode → *10SSSSSEEEEE#* SSSSS= starting user address / EEEEE= ending user address	Enter Program Mode → *10SSSSSEEEEE#* SSSSS= starting user address / EEEEE= ending user address
Delete all tags			Enter Program Mode → *2929#*	Enter Program Mode → *2929#*

4. Enroll / Delete Finger (837EF)

Controller / Functions	Software	E Series Controller with LCD Screen	E Series Controller with Keypad	H Series Controller
Enroll	❌		❌	❌
Delete	❌		❌	❌

Controller / Functions

Software

E Series Controller with LCD Screen

E Series Controller with Keypad

H Series Controller

Enroll

❌

Delete

❌

5. Access / Arming Mode Setting (Setiing details and relevent introduction please refer to the manual.)

Controller / Functions	Software	E Series Controller with LCD Screen	E Series Controller with Keypad	H Series Controller
Access Mode Setting	❌		Enter Program Mode → *04N#** 【N=Access Mode,4=M4；8=M8】	Enter Program Mode → *04N#** 【N=Access Mode,4=M4；8=M8】
Enable / Disable Arming Mode		Enable: ------------------------------------------------------------------- Disable:	present card+NNNN# NNNN：Arming PWD U＝Enable target unit (0=Controller , 1=WG Reader)	In programming mode : Arming：Enter Program Mode →*# Arming：Enter Program Mode →# Not in programming mode : Input Arming PWD（default value :1234） Open door and enable / disable arming in meanwhile： Normal Access Procedure → Input 4-digit Arming Code →# Enable / Disable： →Input 4-digit Arming Code→Present Valid Card
Enabling or Disabling each device into arming status	❌	❌	*Card+NNNN#U#** NNNN：Arming PWD U＝Enable target unit (0=Controller , 1=WG Reader)	❌
Enabling all device into arming status	❌	❌	Card+NNNN#** NNNN：Arming PWD U＝Enable target unit (0=Controller , 1=WG Reader)	❌
Arming PWD			*17PPPP#** PPPP = Arming PWD (0001-9999, default value：1234)	*(M4/M8)17PPPP#** PPPP = Arming PWD (0001-9999, default value：1234)
Arming Delay			❌	❌
Disabling all device into arming status	❌	❌	*Card+NNNN9#** NNNN：Arming PWD U＝Enable target unit (0=Controller , 1=WG Reader)	❌

6. Node ID Setting

Controller / Functions	Software	E Series Controller with LCD Screen	E Series Controller with Keypad	H Series Controller
Node ID setting			*00NNNMMMAAA#** 【NNN=Controller Node ID (Range 001~254),or (Range001~016) when connected with AR-716E】	*00NNN#** 【NNN=Controller Node ID (Range 001~254),or (Range001~016) when connected with AR-716E】
IP Address Setting (enable for new IP Address while power re-transmission )	❌		*010CCCCCCCCCCCC#* Default Value：192.168.1.127 (CCCCCCCCCCCC = 192168001127) set as 000.000.000.000 for IP Address Auto Research (DHCP)	❌
			Net Mask IPv4 : *011255255255000#*	❌
			Gateway (IPv4) : *012192168001254#*	❌

7. Time /Delay Setting

Controller/ Functions	Software	E Series Controller with LCD Screen	E Series Controller with Keypad	H Series Controller
Door Relay Time setting	❌		*02UTTT#* U＝Controller Mode (0=AR-725-E，1=WG Reader) TTT＝Door Relay Time 000 for Normal Launch On ; 001~600＝1-600 sec； 601~609＝0.1~0.9 sec	*02TTT#** TTT=Door Relay Time 000=Normal Launch On 001~600=1sec~600sec 601~609=0.1sec~0.9sec
Alarm Relay Time setting	❌		*03TTT#** TTT＝Alarm Relay Time； 000 (Normal Launch On) Time Range：001~600＝1~600sec	*03TTT#** TTT＝Alarm Relay Time； 000 (Normal Launch On) Time Range：001~600＝1~600sec
Arming Delay Time setting			*05TTT#** Base on second, range: 001~255	*05TTT#** TTT=the buffer time before entering arming mode 001~600=1秒~600秒
Alarm Delay Time setting			*06TTT#** Base on second, range: 001~255	*06TTT#** TTT=the buffer time before the alarm is activated 001~600=1~600 sec
Arming Pulse Time setting			*14TTT#** Base on 1ms, range:1~255, default value=10, Input 0= Timeless	*14TTT#** TTT=Arming output time; 000=output continuously 001~250=0.1~2.5 sec.
Door Close Delay Time			*18UTTT#* U＝Enable target unit (0=AR-725-E , 1=WG Reader) TTT＝Door Close Delay Time (001~255sec，default value：15sec)	*18TTT#** TTT＝Door Close Time: 001~600=1~600 sec.; default value: 15 sec.
Same Tag Reading Interval Time	❌		*31TTTT#** TTTT=10~6000 (Base on 10ms, range from 10 to 6000 ; default value: 1 sec.：0100)	*31TTTT#** TTTT=10~6000 (Base on 10ms, range from 10 to 6000 ; default value: 1 sec.：0100)
Controller Time Clock Setting			*25YYMMDDHHmmSS#** YYMMDDHHmmss= Year / Month / Day / Hour / Min / Sec	*25YYMMDDHHmmSS#** YYMMDDHHmmss= Year / Month / Day / Hour / Min / Sec
Alarm Setting			*32SSHHMMTT7123456#** SS= 16 sets auto alarm schedule, range 0~15 HHMM= HH:MM (ex. 0830: Ring bell at 08:30) TT=Period of time to ring bell (Base on second, range 01~99 sec.) 7123456: 7 days of week -Sun/Mon/Tue/Wed/Thu/Fri/Sat (Input value: 0=disable; 1=enable) H: Holiday (Input value: 0=disable; 1=enable)	❌
Holiday Setting		❌	*35MMDDF#* MM：Month；DD：Day ； F：0 Delete；F：1 Add	❌

8. Anti-pass-back

Controller / Functions	Software	E Series Controller with LCD Screen	E Series Controller with Keypad	H Series Controller
Anti-pass-back (Enable user address)			*26SSSSSEEEEEP#** SSSSS=Starting User Address; EEEEE=Ending User Address; N=0: Enable; N=1: Disable; N=2: Reset	*26SSSSSEEEEEP#** SSSSS=Starting User Address; EEEEE=Ending User Address; N=0: Enable; N=1: Disable; N=2: Reset
Anti-pass-back (Enable Controller)			Enter Program Mode → *20UDDD#* 【U＝ (0=AR-725-E , 1=WG Reader)】【20* please refer to Function Default Value】	Enter Program Mode → *20DDD#** 【128=anti pass back function (0=disable；1=enable)； 064=set as Exit / Entry (0=Exit；1=Entry)】

Controller / Functions

Software

E Series Controller with LCD Screen

E Series Controller with Keypad

H Series Controller

Anti-pass-back (Enable user address)

26*SSSSS*EEEEE*P#
SSSSS=Starting User Address;
EEEEE=Ending User Address;
N=0: Enable; N=1: Disable; N=2: Reset

Anti-pass-back (Enable Controller)

Enter Program Mode → 20*U*DDD#
【U＝ (0=AR-725-E , 1=WG Reader)】
【20* please refer to Function Default Value】

Enter Program Mode → 20*DDD#
【128=anti pass back function
(0=disable；1=enable)；
064=set as Exit / Entry
(0=Exit；1=Entry)】

9. Lift Control Setting

Controller / Functions	Software	E Series Controller with LCD Screen	E Series Controller with Keypad	H Series Controller
Lift control setting: single floor(M4/M8)			*27UUUUULL#* UUUUU＝user address； LL：Floor number(01~64 floor)	(M4/M8 Mode)*27UUUUUFF#* UUUUU=User Address; FF=Floor (01~32 floor)
Lift control setting: multi-floor(M4/M8) (Details please refer to the manual of each Controller)			*21UUUUUGLLLLLLLL#** UUUUU＝user address；G=4 sets of lift control(0~3); LLLLLLLL=8 assigned floor (F=0: Disable, 1: Enable)	*21UUUUUSFFFFFFFF#** UUUUU=User Address, S=4 sets of lift control (0~3); FFFFFFFF=8 assigned floor (F=0: Disable, 1: Enable)
AR-401-IO-0016R Lift Relay Activated TM (M4/M8)			*23MMMTTT#* MMM=Node ID of lift controller TTT= relay time: 000~600=1~600 sec	*23MMMTTT#* MMM=site number, TTT= relay time: 000~600=1~600 sec

10. Controller Additional Function Setting

Controller / Functions	Software	E Series Controller with LCD Screen	E Series Controller with Keypad	H Series Controller
RS485 port function setting (Needs to be restarted after setting)			*37AB#** A＝0:AR401RO 1:Host (Default Value) 2:LED Panel 3:Printer ---------------------------------- B＝0: 9600 (Default Value) 1: 19200 2: 38400 3: 57600	❌
Change WG bits output format	❌	❌	*41n#** n：0＝WG26 n：1＝WG34	❌
※Enable the RF after door sensor closed to GND	❌	Auto enable after firmware upgrade	Auto enable after firmware upgrade	Enable: *34001# Disable: 34000#* (Default Value)
※Turn off all sounds of beeper	❌		Enable:*34001# ( Turn off ) Disable: 34000#* (Default Value)	Enable: *34001# Disable: 34000#* (Default Value)
Enable/Disable keypad lock		press *# simultaneously (do not enter program mode) Enable：Keyboard Lock Disable：Keyboard Unlock	※Enable :*34064# Disable: 34000#* (Default Value)	press *# simultaneously (do not enter program mode) Enable：Keyboard Lock Disable：Keyboard Unlock
※Enable/Disable“#” as Door Bell ( Use Alarm output as Door Bell )	❌	Enable/Disable“#”as Door Bell 0: disable (default value) / 1: enable	*46n#** 0: disable (default value) / 1: enable	Enable : *24128#** Disable: 24*000# (Default Value)

11. Auto Open Time Zone Function Setting

Controller / Functions	Software	E Series Controller with LCD Screen	E Series Controller with Keypad	H Series Controller
Enable / Disable Auto Open Time Zone (open door need to present first valid card)			Enable : 20UDDD# Disable : 20U000# 【U = Reader Code (0 = AR-725-E, 1 = WG Reader)】【Please refer to the Compound Command Function List for calculation method】	Enable : 20004# Disable : 20000#
Enable / Disable Auto Open Time Zone Open Door without Present First Valid Card			Enable : 24U128# Disable : 24U000#	Enable : 24128# Disable : 24000#
Auto-open time zone setting			*08MWNNHHMMhhmm7123456H#* M＝AR-725-E；W=WG Reader (0：disable，1：enable) NN＝00~15 (time zone) HHMM＝begin time ; hhmm＝end time (ex：08301200＝08：30 to 12：00) 7123456H：Sun,Mon,Tue,Wen,Thu,Fri,Sat,Holiday (0：disable，1：enable)	*08NNHHMMhhmm7654321H#** NN＝00~15 (time zone) HHMM＝begin time ; hhmm＝end time (ex：08301200＝08：30 to 12：00) 7123456H：Sun,Mon,Tue,Wen,Thu,Fri,Sat,Holiday (0：disable，1：enable)